Floor Refinishing in Winters

Winters Conditions That Affect Floor Refinishing

Winters sits at about 135 feet in Yolo County. The regional Sacramento Valley record shows summer air cycling widely within each day rather than staying uniformly dry. In the National Weather Service publication "Climate of Sacramento, California" (revised August 2010), average relative humidity at Sacramento is 78 percent at 4 AM against 30 percent at 4 PM in July, a swing of roughly 48 points inside the same day. Those are Sacramento readings taken about 26 miles from Winters, not local measurements. Winters summers near 95°F change the finishing schedule more than the sanding. Waterborne finishes flash off faster in hot, dry air, which shortens the working window and makes lap marks easier to leave behind; we adjust application pace and airflow to the conditions in the house that day rather than to a fixed timetable.

NOAA 1991-2020 normals for the Winters station record a January mean daily maximum of 56.5°F and mean daily minimum of 37.5°F, with January and December each averaging roughly 5 inches of precipitation. Winter is the wet season; summer months average near zero. Cold, damp conditions do the reverse and stretch cure times, which mostly costs patience — a floor that is walkable is not yet a floor that is ready for furniture or rugs.

Seasonal Gaps in Winters Floors, by the Numbers

Seasonal gaps between boards are a common reason people ask about refinishing, and Winters's measured climate shows how much of that gapping is simply the wood moving with the seasons. Measured at University Airport, Davis, then brought to 70°F, the air averages 37.4% relative humidity over the heating season and 56% over summer, which settles wood at roughly 7.3% and 10.3% moisture content. For a traditional 2¼-inch oak strip floor that is about 0.025 inch of seasonal shrinkage per board (about 1/39 inch); for 5-inch plank, about 0.056 inch. Gaps in that range that open in winter and close by summer should not be filled — filler packed into a winter gap gets crushed out, or pushes the boards toward cupping, once the wood takes its moisture back.

Source: Hourly ASOS dewpoint observations 2015–2025, Iowa Environmental Mesonet (Iowa State University); equilibrium moisture content from USDA Wood Handbook FPL-GTR-190 Eq. 4-5; movement from FPL-GTR-282 Eq. 13-3 and Table 13-5

What's Under the Finish

Foundation type is not published for Winters, but the ground under the town is mapped in detail. USDA-NRCS SSURGO maps sixteen soil units inside the city limits. Brentwood silty clay loam is the largest at 31.4% of the incorporated area and carries a linear extensibility of 7.5%; Rincon silty clay loam covers a further 20.4% at 6.4%. NRCS rates any soil above 6% linear extensibility as high shrink-swell, and on that measure 57.9% of Winters sits on high-shrink-swell ground. What Winters does not have is any very-high soil: the most expansive unit in town, Capy silty clay, reaches 8.7% across 4.5% of the area, and nothing crosses the 9% threshold. Set against Dixon ten miles southeast, where no unit in the city rates above moderate at all, Winters is meaningfully more seasonally active ground — but it is not Diablo-clay country either.

A slab affects what can be refinished at all. Wood over concrete is usually engineered or glued-down, and an engineered floor can only be sanded if its wear layer is thick enough to survive it — some can take a full sanding, many can take one light pass, and some cannot be sanded at all. We measure the wear layer before quoting rather than after starting.

Raised floors are where the best refinishing candidates live: solid wood over a crawlspace, often with decades of wear and plenty of thickness left. It is also where cupping comes from. Sanding a cupped floor flat before the crawlspace moisture is fixed produces a floor that goes concave the other way once it dries — so the moisture reading comes first and the sanding comes second.

Source: NAHB analysis of the Census Bureau Survey of Construction, foundation type by region (2024)

Winters Homes We Work In

ACS 2020-2024 five-year estimates count 2,564 housing units. The largest cohorts were built 1980-1989 (21.8%) and 1970-1979 (17.7%). Winters also retains a comparatively large pre-1940 cohort at 8.9% of units, alongside continued recent construction: 6.8% of units were built 2020 or later. Winters's 1970s-1980s, 2000s, and pre-1940 stock is where refinishing pays off most: homes of that period often have original wood under carpet, and when the wear layer is intact, refinishing keeps a floor that cannot be bought new. We check thickness at a vent or a doorway before recommending it.